SuperCAT4 and T1 Transmitter Configurator

Super C.A.T4
Dynamic range	120 dB at 10Hz
Dynamic overload protection	40 dB at 50Hz (automatic)
Depth accuracy**	Cables: ± 5% tolerance 0.1m at 3m Sondes: ± 5% tolerance 0.1m at 7m
Locating accuracy	± 10% of depth
Batteries	2x D-cell (LR20) alkaline batteries
Weight	2.3kg (including alkaline battery)
Dimensions (HxWxD)	710x255x65mm
Material	Injection-moulded plastic
Protection class	IP54 (dust and splash water protected)
Operating temperature	-20°C to +50°C
Storage temperature	-20°C to +70°C
Data interface	USB 2.0

** Super C.A.T4 can locate at greater depths, but with reduced accuracy.

 

Super C.A.T4+ Technical Data			Locating depth guidance (m)
Locating performance	Frequency range	Sensitivity at 1m	Good conditions	Poor conditions
Power signals (P)	50Hz - 1.5kHz	3 mA	3	2
Radio signals (R)	15kHz - 30kHz	25 µA	2	1
Active frequencies	512/640Hz 8kHz 33kHz 65kHz 131kHz	500 µA 100 µA 5 µA 5 µA 5 µA	4	2
Sonde frequencies	512/640Hz 8kHz/33kHz	N/A	Up to 15m

 

SuperC.A.T4+

Designed for use in demanding construction environments, this locating receiver can be combined with a wide range of sondes and accessories.
 

Locate and protect buried utilities

Safe excavation work depends on the accurate locating of underground utilities. Failure to correctly identify existing utilities can lead to damage to underground pipes and cables. This can result in service outages, costly repairs and project delays. In some cases, it may also cause accidents with injuries.

 

APPLICATIONS

Each model in the SuperCAT4+ and T1 series has been developed to meet the requirements of a specific industry.

SuperC.A.T4+
Construction industry
Designed for use in demanding (civil) construction environments, this receiver can be used with a wide selection of sondes and accessories.

SuperCAT4+ locates a comprehensive range of active frequencies to support the detection and tracing of different cable types in various environments.

Higher frequencies, such as 131kHz or 65kHz, can be used for locating well-insulated, high-impedance utilities such as telecom cables or insulated pipe joints.

In environments where mainly telecommunications cables and high-impedance utilities are located, the T1-131 with the higher frequency range should be used. Alternatively, for a lower frequency range suitable for locating pipes, it can also be used with parameters 65 / 512 / 640.

SuperC.A.T4+ S
Water and pipeline industry
For detecting and tracing buried pipes, SuperCAT4+ S locates the widest range of sonde frequencies.

The S model locates a range of sonde frequencies tailored to the requirements of locating water and drainage pipes and ducts. Low-frequency sondes are suitable for cast iron pipes. Higher frequency sondes are used for locating non-metallic pipes and ducts.

Additionally, for continuous signal tracing using a T1-512 or -640, an active 33kHz frequency can be coupled onto a FlexiTrace.

SuperC.A.T4+ CPS
Construction industry / Gas utilities
Optimised for oil and gas pipelines (metal pipes) carrying direct current for cathodic corrosion protection (CPS). The CPS signal can be located and traced without coupling an additional transmitter signal onto the line.

T1 Transmitter
Signal output power (inductive)	0.1 W
Signal output power (galvanic)	1.0 W
Data interface	USB 2.0 - for future applications
Batteries	4x D-cell (LR20) alkaline batteries
Weight	1.7kg (including batteries)
Dimensions (HxWxD)	90x75x265mm
Material	Injection-moulded plastic
Protection class	IP54 (dust and splash water protected)
Operating temperature	-20°C to +50°C
Storage temperature	-20°C to +70°C

 

Inductive frequencies:	T1-640	T1-640/65	T1-131
8kHz	✔	✔	✔
33kHz	✔		✔
65kHz		✔
Galvanic frequencies:	T1-640	T1-640/65	T1-131
640Hz	✔	✔
8Hz	✔	✔	✔
33Hz	✔		✔
65Hz		✔
131Hz			✔

 

T1 Transmitter

The T1 is a universal 1-watt signal transmitter that provides three locatable frequencies, two induction frequencies and two power levels. As standard, the T1 induces its signal directly into the ground.

It is the perfect companion for cable and pipeline locating for the SuperC.A.T4 series. The T1 transmitter is used to actively couple a locating signal onto cables or metal pipes. This signal can then be located with a receiver.

The T1 transmitter stands out for its compact design and ease of use. In contrast to the Genny4 transmitter, the T1 transmitter offers a wider frequency spectrum than the Genny4.

The T1 transmitter was developed for the SuperC.A.T4 series. With this combination for advanced utility locating, cable and pipeline routes can be traced with real-time depth measurement.

Available transmit methods

INDUCTIVE

The T1 has an internal antenna that induces a signal onto the utility/ies directly beneath the unit. This is helpful when the utility is not directly accessible. Normally, induction mode is effective only to a depth of 2m. Note that induction mode couples its signal indiscriminately to all conductors within its transmission range.

Induction mode is available only at frequencies of 8kHz and higher.

DIRECT (galvanic) connection

Direct connection is an effective method of applying the T1 locating signal to a specific cable or pipeline so that it can be traced above ground. The connection can be made to any metallic part of the pipe or cable, such as valves, meters, distribution cabinets, street lights, pipeline markers or other access points.